30V36V
75793CD07②If the indicator is below 24V, it means that the electricity is being discharged. If the indicator is above 30V, an unusually high volt-age may damage the alternator. Check the charging system in both cases.7-223)WARNING LAMPSEmergency warning lampT/M oil temperature warning lampEngine overheat warning lampHydraulic oil temperature warning lampFuel level warning lampT/M error warning lampAir cleaner warning lampEngine oil pressure warning lampSteering warning lamp(Primary)Battery charging warning lampSteering warning lamp(Emergency)Brake fail warning lamp7809S7EL31(1)Emergency warning lamp①This warning lamp blinks and the buzzer sounds when comuni-cation error occur between monitor and MCU.②When this warning lamp blinks, machine must be checked and service immediately.75793CD95(2)Engine overheat warning lamp①This lamp is turned ON when the temperature of coolant is over the normal temperature 106˚C (223˚F).②Check the cooling system when the lamp is ON.77073CD17(3)Transmission oil temperature warning lamp①This lamp informs the operator that transmission oil is above the specified temperature.②When this lamp lights up during operation, stop the engine and check the machine.75793CD357-23(4)Hydraulic oil temperature warning lamp①This warning lamp operates and the buzzer sounds when the temperature of hydraulic oil is over 105˚C (221˚F).②Check the hydraulic oil level when the lamp is turned ON.③Check for debris between oil cooler and radiator.77073CD21(5)Fuel level warning lamp①This warning lamp lights ON when the fuel level is low.Refuel the machine as soon as possible.77073CD23(6)Transmission error warning lamp①This lamp lights ON and the LCD display show the error codes when an error occurs in the transmission.②Immediately pull the machine to a convenient stop. Stop the engine. Investigate the cause.77073CD19※Consult a HYUNDAI dealer to investigate the cause.※Do not operate until the cause has been corrected.(7)Air cleaner warning lamp①This lamp lights ON when the filter of air cleaner is clogged.②Check the filter and clean or replace it when the lamp is ON. 77073CD20(8)Engine oil pressure warning lamp①This lamp is comes ON after starting the engine because of the low engine oil pressure.②If the lamp comes ON during engine operation, shut OFF engine immediately. Check engine oil level.77073CD187-24(9)Steering warning lamp①PrimaryThis lamp indicates that the primary steering has failed. When the indicator comes on and the action alarm sounds, steer the machine immediately to a convenient location and stop the machine. Stop the engine and investigate the cause.※Do not operate the machine until the cause has been cor-rected.②EmergencyThis lamp indicates the emergency steering system is active.※Immediately pull the machine to a convenient stop and stop the engine.※The emergency steering system can be manually tested. The emergency steering system can be manually tested. Refer to page 7-46.77073CD6677073CD15(10)Battery charging warning lamp①This lamp is ON when key ON, it is turned OFF after starting the engine.②Check the battery charging circuit when this lamp comes ON, during engine operation.77073CD22(11)Brake fail warning lamp①The lamp lights ON when the oil pressure of service brake drops below the normal range.②When the lamp is ON, stop the engine and check for its cause.※Do not operate until any problems are corrected.77073CD167-254)PILOT LAMPSWarming up pilot lampMirror defrost pilot lampPreheater pilot lampSeat belt pilot lampFuel warmer pilot lampHigh beam pilot lampParking brake pilot lampFan reverse pilot lampMaintenance pilot lampDifferential lock pilot lampClutch cut off pilot lampRide control pilot lamp(Auto)Ride control pilot lamp(On)7809S7EL32(1)Warming up pilot lamp①This lamp is turned ON when the coolant temperature is below 30˚C (86˚F).②The automatic warming up is cancelled when the engine coolant temperature is above 30˚C, or when 10 minutes have passed since starting the engine.75793CD31(2)Seat belt pilot lamp①This lamp lights ON for the first five seconds after starting the engine.75793CD17(3)Mirror defrost pilot lamp①This lamp comes ON when mirror defrost switch is pressed.7807A3CD117-26(4)High beam pilot lamp77073CD12(5)Preheat pilot lamp77073CD14(6)Parking brake pilot lamp77073CD13(7)Maintenance pilot lamp75793CD32(8)Clutch cut off pilot lamp77073CD65①This lamp works when the illuminating direction is upward.②This lamp comes ON when the dimmer switch is operated, e.g., when passing another vehicle.①This lamp lights ON when start switch is turned clockwise to the ON position. Light will turn off after approximately 5~45 sec-onds, depending on engine temperature, indicating that preheat-ing is completed. ②When the lamp goes out the operator should start cranking the engine.①When the parking brake is actuated, the lamp lights ON.※Check the lamp is OFF before driving.①This lamp will be ON when the consuming parts are needed to change or replace. It means that the change or replace-ment interval of the consuming parts remains below 30 hours.②Check the message in maintenance information of the moni-tor menu. Also, this lamp lights ON for 3 minutes when the start switch is ON position.①This lamp lights ON when the clutch cut off mode switch is positioned L, M, H.※ReferRefer to page 7-46. to page 7-46.7-27(9)Ride control pilot lampRide control pilot lamp (option)①Auto ride controlThis lamp lights ON when push in the bottom of the ride control switch (auto position).※Refer to page 7-45.75793CD33②Manual ride controlThis lamp lights ON when push in the top of the ride control switch (manual position)※Refer to page 7-45.75793CD34(13)(10)Fan reverse pilot lamp①This lamp lights ON when the fan control switch is pressed.※Refer to page 7-45.7707A3CD40(11)Differential lock pilot lamp①This lamp lights ON when the differential lock function isoperating.78093CD33(12)Fuel warmer pilot lamp①This lamp is turned ON when the coolant temperature is below 10˚C (50˚F ) or the hydraulic oil temperature 20˚C ( 68˚F ). ②The automatic fuel warming is cancelled when the engine coolant temperature is above 60˚C and the hydraulic oil tem-perature is above 45˚C since the start switch was ON position.21093CD437-285)LCDType 1232175793CD39(1)The LCD can be used with the gear selector.It indicates speed and driving direction.NoSymbolMeaningRemarkForward, reverse, neutral11, 2, 3, 4P23,Forward, reverseGear range displayActual gear displayActual gearParking brake mode activeAutomatic modeAutomatic mode7-292. MONITOR2. MONITOR·The monitor is adjustable. - Vertical : 14˚ - Horizontal : 30˚
VerticalMain display
HorizontalMenu buttonLeft move button
Camera / ESC buttonEnter buttonRight move /
buzzer stop button
75793CD231)BUTTONS(1)Menu button①Main display to main menu, main menu to main display.②AEB cancel button in AEB setting.75793CD90(2)Left move button①Move in menu (left, up).75793CD91(3)Camera / ESC button①Enter rear camera mode in main display.②Cancel button except in main display (move previous menu).75793CD92(4)Right move / Buzzer stop button①Move in menu (right, down).②Buzzer stop.75793CD93(5)Enter button①Select menu (enter).②AEB cancel button in AEB setting.75793CD947-302)MAIN MENUMain display
145
TYPE A (default)
2567
TYPE B
75793CD11367
Main menu
10
Press
10
1 Buzzer 5 Select gear 2 Clock 6 Engine mode 3 Wiper speed 7 Transmission mode 4 Actual gear 8 Engine rpm※Display type can be changed by operator. See page 7-41.(1)StructureNoMain menuSub menuEngine speed Kick downWiper speedFan-auto modeAEBSpeed meterFault codeMachine monitoring2MONITORING75793CD13 9 Hour meter, odometer 10 MonitoringDescriptionEngine warming up, Engine speedMode 1 (down/up), Mode 2 (down only)4 stepsInterval and time settingAEB settingPulse settingActive, Logged fault (Machine, ECU, TCU)Hyd temp, Battery, Coolant tempT/M oil tempHour meter, ODO meter1MODE75793CD12Monitoring history3MANAGEMENT75793CD14Machine securityMaintenanceMachine informationService contactService menuClockDisplayESL system setting, Change passwordReplacement, Change interval (oils and filters)Version, Status Service contactS/W downloadClockBrightness setting (Manual/Automatic)Type display (A or B type)Temp (˚F/˚C), Distance (km/mile), Pressure (bar, Mpa, kgf/m2, psi)Reverse mode, Active camera, Display order12 languages4UnitDISPLAY SET UPRear cameraLanguage75793CD137-31(2)Mode①Engine speed75793CD1675793CD16A75793CD16BSet low idling speed75793CD16C75793CD16D②Kick down75793CD1775793CD17A·Mode 1 (down/up) : Press kick down button once, shift down and press button again, shift up.·Mode 2 (down only) : Press kick down button every time, shift to lower gear respectively.※Refer to page 7-48.③Wiper speed75793CD1875793CD18A·Setting wipe speed 1 to 4.④Fan-auto mode75793CD11075793CD11175793CD112·Select reverse interval or reverse time.·Set reverse interval (30~300 min) or reverse time (30~300 sec).※Default : Interval (60 min), time (120 sec)※Refer to page 7-45, fan control switch.7-32⑤AEBActual gear window
75793CD1975793CD19A·AEB mode controls the disk clearance of the transmission, automatically.·To start AEB setting, press and hold for 3 seconds.·To cancel AEB setting, press , or . ·If \"OK\" in actual gear window, press , or to complete AEB setting.·Display during AEB modeSymbolSTK1~K4, KV, KROK*Spanner and Kx*△E▽E△T▽TFO*FN*FP*Start AEBCalibrating clutch K1~K4, KV or KR respectivelyCalibration for all clutches fi nishedKx couldn't be calibrated, AEB fi nishedEngine speed too low- Raise engine speedEngine speed too high- Lower engine speedTransmission oil temperature too low- Heat up transmissionTransmission oil temperature too high- Cool down transmissionOutput speed not zeroShift lever not in neutral positionParking brake not appliedMeaning: Transmission stays in neutral, you have to restart the TCU (ignition off/on).*: ⑥Speed meter75793CD2075793CD20B75793CD20A·Press and hold for 3 seconds.·To change the pulse value, press or .·To change the position, press .※Only for the serviceperson.7-33(3)Monitoring①Fault code75793CD2375793CD23C7709S3CD23D75793CD23E7709S3CD237709S3CD23G75793CD23H75793CD23I75793CD23J·Monitor the fault code of the Machine / ECU / TCU .※Not define will be indicated in case of that there's no fault.7-34②Machine monitoring75793CD247709S3CD24A7709S3CD24B·Monitor the status of the machine.·To check the item in main display, choose it and press . ·The right icon shows ON / OFF status.③Record monitoring75793CD2575793CD25A75793CD25C·Hour meter- TTotal : total hour meterotal To show the item in the main display, select \"ON\" and press (this item could not reset).- LatestLatest : the latest hour meter after reset.To show the item in the main display, select \"ON\" and press . To reset the latest hour meter, select \"initializing\" and press . 75793CD25D75793CD25F75793CD25H·ODO meter- TTotal : total ODO meterotal To show the item in the main display, select \"ON\" and press (this item could not reset).- LatestLatest : the latest ODO meter after reset.To show the item in the main display, select \"ON\" and press . To reset the latest odometer, select \"initializing\" and press . 7-3575793CD25J(4)Management①Machine security75793CD2675793CD26A75793CD26B·ESL system setting-ESL : Engine Starting Limit-ESL mode is designed to be a theft deterrent or will pre-vent the unauthorized operation of the machine.-If the ESL mode was selected Enable, the password will be required when the start switch is turned ON.-Disable : Not used ESL functionEnable : The password is required whenever the operator start engine.Interval mode : The password is required when the opera-tor start engine fi rst. But the operator can restart the engine within the interval time without inputting the password.The interval time can be set maximum 2 days.※Default password : 0000075793CD26C*75793CD26D·Interval setting- If set interval setting to 5 minutes, ESL system is activated after 5 minutes.Therefore, the password does not need to restart engine within 5 minutes.75793CD26J75793CD26K7-36·Change password-Input 5 to 10 digits and press *.75793CD26GEnter the current password.75793CD26H75793CD26LEnter the new password.75793CD26N75793CD26MThe new password is stored in the MCU.Enter the new password again.7-37②Maintenance75793CD2775793CD27A75793CD27B75793CD27D75793CD27C·Alarm ( ) : WarningReplacement : The elapsed time will be reset to zero.Change cycle : The change or replace cycle can be changed in the unit of 50 hours.·To change cycle, press or .·Change or replace intervalNo12345671011Engine oilHydraulic oilItemInterval500★1 2000★2 5000Pilot line fi lter elementHydraulic oil return fi lterEngine oil fi lterFuel fi lter elementFuel pre-fi lterHydraulic tank air breatherRadiator coolantTransmission oil and fi lterAxle oil (front and rear)250250500500500250200010001500★1 : Conventional hydraulic oil★2 : Hyundai genuine long life hydraulic oil7-38③Machine information75793CD2875793CD28A7809S3CD28B75793CD28C75793CD28D·Version- Software versions of MCU, cluster and monitor can be checked.·Status info- The machine status can be checked.75793CD28E④Service contact75793CD2975793CD29A75793CD29B·The phone number of the service man can be checked and changed.⑤Service menu75793CD3075793CD30A75793CD30B·The software of monitor can be downloaded.7-39(5)DISPLAY SET UP①Clock75793CD3275793CD32A·To set time, press or .·To move position, press .②Display·Brightness setting75793CD3375793CD33A75793CD33B75793CD33CManual (1st~8th step)75793CD33D75793CD33EAuto (day / night)※If \"Automatic\" is chosen, brightness for day and night can be differently set up. Also by using the bar in lower side, users can defi ne which time interval belongs to day and night.(in bar fi gure, gray area represents night time while white shows day time)7-40·Display type75793CD33F75793CD33G75793CD33HA type75793CD33IB type③Unit75793CD3475793CD34A75793CD34B·Temperature : ˚C ↔ ˚F·Distance : km ↔ mile·Pressure : bar ↔ Mpa ↔ kgf/m2 ↔ psi7-41④Rear camera75793CD3575793CD35A75793CD35B75793CD35C75793CD35D75793CD35E75793CD35F·Reverse mode- If transmission engages the reverse gear (R1~R3), the camera mode is displayed automatically in main display.·Active camera- Three cameras can be installed on the machine.- The display order can be set by this menu.·If the camera was not equipped, this menu is not useful.·In main display, if the button is pushed, the fi rst ordered display camera will be viewed.⑤Language75793CD3675793CD36A75793CD36B·User can select preferable language and all display are changed the selected language.7-423. SWITCHES3. SWITCHESCab ceiling LH sideMirror defrost switch(option)Rear wiper/washer switchBeacon switch(option)USB socketAMMFan control switchEmergency test switch(opt)Main light switchWork lamp switchKick down switchHazard switchT/M shift mode switchClutch cut off mode switchMulti function switchHorn buttonStarting switchEngine mode switchParking brake switchRide control switch(opt)Differential lock switch(opt)PMA7809S3CD291)STARTING SWITCH(1)There are three positions, OFF, ON and START.· (OFF) : None of electrical circuits activate.· (ON) : All the systems of machine operate.· (START) : Use when starting the engine. Release key immediately after starting.※If you turn ON the starting switch in cold weather, the fuel warm-er is automatically operated to heat the fuel by sensing the cool-ant temperature. Start the engine in 1~2 minutes after turning ant temperature. Start the engine in 1~2 minutes after turning ON the starting switch. More time may take according to ambi-ent temperature.※Key Key must be in the ON position with engine running maintain must be in the ON position with engine running maintain electrical and hydraulic function and prevent serious machine electrical and hydraulic function and prevent serious machine damage.7-4377073CD412)HAZARD SWITCHONOFF(1)Use for parking, or loading the machine.(2)Both turn signal lights will flash simultaneously.※If the switch is left ON for a long time, the battery may be dis-charged.75793CD423)PARKING BRAKE SWITCH(1)When the switch is pressed to ON position, the parking brake will Safety buttonstart to operate and the cluster warning lamp will comes ON.ONReleasePLockUnlock75793CD44(2)Press the release position in order to disengage the parking brake.※When operating the gear selector lever, be sure to release the When operating the gear selector lever, be sure to release the parking brake. If the machine is operated with the parking brake engaged, the brake will overheat and may cause the brake sys-tem to go out of order.※This switch can be set to ON or Release position only when the safety button is pulled to the unlock position.4)MAIN LIGHT SWITCH(1)This switch use to operates the clearance lamp and head light by two step.·First stepFirst step : Clearance lamp and cluster illumination lamp comes ON. Also, all indicator lamp of switches come ON.·Second stepSecond step : Head light comes ON.75793CD455)WORK LAMP SWITCH(1)This switch use to operates the front and rear work lamps by two step.·First stepFirst step : Front work lamp located on the cab comes ON.·Second stepSecond step : Rear work lamp located on the cowl comes ON.75793CD466)REAR WIPER AND WASHER SWITCH(1)The switch use to operates the rear wiper and washer by two step.·First stepFirst step : The rear wiper operates.OFFON·Second stepSecond step : The washer liquid is sprayed and the rear wiper is operated only while pressing. If release the switch, return to the first step position.75793CD477-447)FAN CONTROL SWITCHOFFAUTOMANUAL75793CD49(1)This switch use to control the cooling fan.(2)This switch has three positions.·AUTOUTO : The fan automatically work in reverse according to set up interval and time.※ Refer to page 7-32.·OFF : : Only forward rotation is possible.·MANUAL : The fan rotates reverse only while pressing this position.If release the switch, return to the OFF position.(3)On pressing the switch, the indicator lamp is turned ON.8)MIRROR DEFROST SWITCHMIRROR DEFROST SWITCH (option)(1)If the mirror defrost switch is pressed in condition of key ON, it oper-ates for 15 minutes. After 15 minutes, the defrost function stops automatically.(2)One more pressing the switch in operation also stops defrost func-tion.(3)On pressing the switch, the indicator lamp is turned ON.75793CD4)BEACON SWITCHBEACON SWITCH (option)(1)This switch turns ON the rotary light on the cab.75793CD5010)RIDE CONTROL SWITCHRIDE CONTROL SWITCH (option)OFFMANUALAUTO75793CD51(1)AUTO Press in the bottom of the ride control switch in order to turn on the automatic ride control. The automatic ride control automatically turns on when the travel speed exceeds a preset speed of approxi-mately 7 km/h. The automatic ride control automatically shuts off dur-ing low speed travel (below 7 km/h).(2)MANUAL Press in the top of the ride control switch in order to turn on the sys-tem for ride control regardless speed. The ride control will smooth the ride of the machine during travel.(3)OFF Press the ride control switch to the middle position in order to turn off the system for the ride control.7-4511)EMERGENCY TEST SWITCHEMERGENCY TEST SWITCH (option)(1)The emergency steering system can be manually tested. Push the switch in order to determine if the emergency steering and the emergency steering lamp are functional.(2)When the switch is pressed, the emergency steering pump motor will run. The emergency steering lamp will light. If the emergency steering lamp does not light, do not operate the machine.12)CLUTCH CUT OFF MODE SWITCH(1)Four modes are available for operator's preference and job condition.·OFF : The clutch cut off function is disable.LMHOFF·L (Low) : The clutch is disengaged early for short-distance and rapid loading.·M (Medium) : The clutch is disengaged normally for general dig-ging and loading operation.·H (High) : The clutch is disengaged lately for slope ground.M mode(2)The clutch cut off functions of the left brake pedal depend on the L modeposition of the left brake pedal and the position of the clutch cut off mode switch.H modeLeft brake pedal 75793CD5813)TRANSMISSION SHIFT MODE SWITCH(1)Four modes are available for operator's preference and job A..ANALcondition..AHMAN·MAN (Manual) : Machine is operated by selected gear on lever.·AL (Auto Light) : Automatic shifting point is fast for long-dis-tance transportation and fuel efficiency.75793CD59·AN (Auto Normal) : Automatic shifting point is normal without automatic kick-down to 1st gear for general digging and loading operation.·AH (Auto Heavy) : Automatic shifting point is normal with auto-matic kick-down to 1st gear for more power-ful operation.14)ENGINE MODE SWITCHS
M75793CD52Positions for clutch cut off functionClutch cut off mode switchLeft brake pedalLL, M, HMM, HHHEP
75793CD57(1)The operator can adjust the machine's performance with this dial switch.·P (Power) : Maximum power output for hard digging operation or hill climb.·S (Standard) : General digging and loading operation.·E (Econo) : Maximum fuel efficiency for general loading.7-4615)DIFFERENTIAL LOCK SWITCHDIFFERENTIAL LOCK SWITCH (option)OFFMANUALAUTOMA78093CD3016)HORN BUTTONHorn button7609S3CD1617)CAB LAMP SWITCHDOOR
ON
75793CD6318)USB SOCKETAUXUSBHB1003CD63(1)This switch is used to apply differential lock.The differential lock gives equal power to both rear wheels and is used in conditions when traction is poor.(2)Manual modePress the top of the switch for the manual mode of the differential lock function. You press the switch, the differential lock will engage immediately and differential lock pilot lamp lights ON.(3)Auto modePress the bottom of the switch for auto mode of the differential lock function. If you press the switch, the axle differential lock will auto-matically engage when the differential function is used.※While the axle differential lock function is operating, the differen-tial lock pilot lamp lights ON.※Refer to page 7-28.(1)If you press the button on the top of the multifunction switch, the horn will sound. (1)This switch turns ON the cab room lamp. ①DOORThe lamp comes ON when the door is opened.When the door is closed the lamp is OFF.② ONThis switch is used to turn the lamp ON or OFF.(1)MP3 files are played when a USB device is connected to the USB port.(2)In addition, the AUX port enables headphone and other devices.7-4719)KICK DOWN SWITCHKick down switch(1)Manual modeIt is effective 2nd speed to 1st speed only and recover to 2nd speed quickly when push the switch one more time.(2)Automatic modeMode 1 (down/up)①Mode 1It shifts down quickly from current gear to one step lower speed by pushing the switch and recover to current speed quickly when push the switch one more time.Mode 2 (down)②Mode 2It shifts down from current gear to one step lower speed when push the switch every time. The kick down function is released in only 1st speed.※Refer to page 7-32 for the kick down setting.The normal autoshift function continues after the kick down ※The normal autoshift function continues after the kick down switch is released.7609S3CD2420)MULTI FUNCTION SWITCHO J Ⅰ Ⅱ(1)Front wiper and washer switch①When the switch is in J J position, the wiper moves intermittently.②When placed in Ⅰ or Ⅱ position, the wiper moves continuously.③ If you push the grip of the lever, washer liquid will be sprayed and the wiper will be activated 2-3 times.73033CD29※ Check the quantity of washer liquid in the tank. If the level of the washer liquid is LOW, add the washer liquid (in cold, winter days) or water. The capacity of the tank is 1 liter.(2)Dimmer switch① This switch is used to turn the head lights direction.② Switch positions·Up : To flash for passing·Middle : Head lights low beam ON·Down : Head lights high beam ON③ If you release the switch when it's in up position, the switch will return to middle.(3)Turning switch① This switch is used to warn or signal the turning direction of the machine to other vehicles or equipment.② Push the lever up for turning left, pull the lever down for turning right.UpMDown73033CD30Left turningRight turning73033CD317-48
因篇幅问题不能全部显示，请点此查看更多更全内容