Network Working Group P. PrindevilleRequest for Comments: 1051 McGill University March 1988 A Standard for the Transmission of IP Datagrams and ARP Packets over ARCNET NetworksStatus of this Memo
This RFC specifies a standard protocol for the Internet community. Distribution of this memo is unlimited.Introduction
This RFC specifies a standard method of encapsulating Internet
Protocol (IP) [1] and Address Resolution Protocol (ARP) [2] datagrams on an ARCNET [3].Acknowledgements
The author wishes to express thanks to Robert Craig of the McGill
University Computing Centre and Bruce Hughes of Datapoint Corporation for their generous support of facilities and information. I also
extend my gratitude to the readers of the PCIP mailing list for their helpful ideas and comments.Frame Format
IP and ARP datagrams are transmitted in standard ARCNET packets. As required by Datapoint Corporation, the first octet of the data field is reserved for the network layer protocol identification (the
\"system code\" in Datapoint nomenclature), and must contain the value 240 (F0 hex) for IP or 241 (F1 hex) for ARP. The ARP hardware address type for ARCNET is 7 [9].
ARCNET supports packet formats containing 1-253 octets of data (normal format) and 257-508 octets of data (extended format),
inclusive of system code. Note that there exists a range of data lengths (254-256) which are ’forbidden’. IP packets within this range should be padded (with octets of zero) to meet the minimum
extended packet size of 257 data octets. This padding is not part of the IP packet and is not included in the total length field of the IP header.
Prindeville [Page 1]
RFC 1051 IP and ARP on ARCNET March 1988 On networks where some hosts do not support extended packet format, the IP Maximum Transmission Unit (MTU) should be set to 253, though implementors are encouraged to support the extended packet format mode of operation.
Because the ARCNET maximum packet length is less than the Internet default MTU, implementations are strongly encouraged to support IP level fragmentation and reassembly. Hosts not supporting this should take steps to discourage others from sending fragmented packets, such as using the TCP Maximum Segment Size option [4]. The frame format is:
Normal Packet Extended Packet +----------------+ +----------------+ | ALERT* | | ALERT* | +----------------+ +----------------+ | SOH (1) | | SOH (1) | +----------------+ +----------------+ | SID | | SID | +----------------+ +----------------+ | | | | + DID + + DID + | | | | +----------------+ +----------------+ | COUNT | | NUL (0) | +----------------+ + + | SYSTEM CODE | | COUNT | +----------------+ +----------------+ | | | SYSTEM CODE | : DATA : +----------------+ | | | | +----------------+ : DATA : | | | | + CRC + +----------------+ | | | | +----------------+ + CRC + | | +----------------+
ALERT*: Six mark bits signifying the beginning of a frame. SID: Sender’s node ID.
DID: Receipient’s node ID (repeated for reliability). COUNT: Length of data and system code (one’s complement). SYSTEM CODE: 240 for IP, 241 for ARP (decimal).
DATA: Is either an IP or an ARP packet, padded with NULs so as to not be between 254 and 256 octets long. CRC: Cyclic redundancy check (CRC-16).
Prindeville [Page 2]
RFC 1051 IP and ARP on ARCNET March 1988Address Mappings
The mappings between 32-bit Internet addresses to 8-bit ARCNET addresses can be done several ways, recommended are: Host Number Extraction
The easiest thing to do is to use the last eight bits of host number part of the Internet address as the host’s node id. This has been implemented on Experimental Ethernet [5] and ProNET-10 [6].
Dynamic Discovery
Mappings between 32-bit Internet addresses and 8-bit ARCNET node ids could be accomplished through ARP. Internet addresses are assigned arbitrarily on some Internet networks. All
implementations supporting ARP must have a means of disabling ARP and using the above Host Number Extraction method of address mapping so that systems may interoperate.
The use of ARP is optional. However, ARP is desirable when using IP implementations that don’t support subnetting [7], as in the Proxy ARP scenario [8].Broadcast Address
The broadcast Internet address (the address on the network with a host part of all binary ones) should be mapped to the broadcast node id 0.
Prindeville [Page 3]
RFC 1051 IP and ARP on ARCNET March 1988References
[1] Postel, J., \"Internet Protocol\ Center, SRI, September 1981.
[2] Plummer, D., \"An Ethernet Address Resolution Protocol\ Network Information Center, SRI, November 1982.
[3] \"ARCNET Designer’s Handbook\ Corporation, 1983.
[4] Postel, J., \"The TCP Maximum Segment Size Option and Related
Topics\ [5] Postel, J., \"A Standard for the Transmission of IP Datagrams over Experimental Ethernet Networks\ Center, SRI, April 1984.
[6] \"ProNET-10 Model p1300 IBM PC Interface System Installation and Programming Guide\ [7] Mogul, J. and J. Postel, \"Internet Standard Subnetting
Procedure\ 1984.
[8] Carl-Mitchell, S. and J.S. Quarterman, \"Using ARP to Implement Transparent Subnet Gateways\ Center, SRI, October 1987.
[9] Reynolds, J., and J. Postel, \"Assigned Numbers\ Network Information Center, SRI, May 1987.
Prindeville [Page 4]